[2025] 300-510 PDF Questions – Perfect Prospect To Go With Free4Dump Practice Exam [Q41-Q64]

Rate this post

[2025] 300-510 PDF Questions – Perfect Prospect To Go With Free4Dump Practice Exam

Cisco 300-510 Pdf Questions – Outstanding Practice To your Exam

Q41. Which attribute is used to instruct the router that packets must be processed by an ASA that is associated with the segment?

service SID with service instructions

node SID that identifies a specific network device

prefix SID that represents a specific route prefix

adjacency SID with unidirectional adjacency instructions

Q42. Level 3 switch SW1 is part of an EIGRP enabled network located at the edge of an are a. Cisco Express Forwarding and SSO are enabled on the router. A network engineer must minimize the downtime of data-transmit services in the network. HSRP group 2 has already been configured with standby preempt delay minimum 2 and standby timers 140. Which additional action must the engineer take on SW1 to suppress routing flaps for 2 minutes?

Configure timers standby 2 wait 2 under the HSRP group 2 configuration.

Configure timers nsf route-hold 120 under the global EIGRP configuration.

Configure timers nsf signal 2 under the global EIGRP IPv4 address family.

Configure timers standby 2 coverage 120 under the HSRP group 2 configuration.

Q43. Refer to the exhibit.

Which task must you perform on interface g1/0/0 to complete the SSM implementation?

configure OSPFv3

enable CDP

disable IGMP

configure IGMPv3

Q44. Refer to the exhibit.

Router 1 and Router2 have shared routes in the OSPF database but the routes are missing from their routing tables. Checking me prefix-list configuration on both routers, the engineer confirmed all networks are allowed What action should the engineer take to fa the problem?

Configure the two routers with different process IDs

Configure the two routers with different hello and dead timer values

Switch the DR and BDR roles between the two routers

Configure interface Senal1/0 on Router1 as a point-to-point interface

Q45. Refer to the exhibit. A customer reports that Host-1 is failing to receive streaming traffic from the IPTV source. The engineer has confirmed that hosts on router R2 are receiving traffic normally and that Host-1 is correctly sending subscription messages to join the IPTV stream.
Which action must the engineer take to correct the problem?

Configure IP PIM SSM and IGMP version 2 under interface GigatxtEthernet 1/0/1 on R3

Configure IGMP version 3 under interface GigabitEthernet 1/(V1 on R3

Remove IP PIM SSM and IGMP from interface GigaEthernet 1/0/1 on R3 and configure under global configuration

Remove IP PIM SSM from the global configuration on R3 and configure it under the GigabitEthernet
1/0/1 interface

Q46. Refer to the exhibit.

Refer to the exhibit An engineer is troubleshooting a networking issue with several symptoms The shortest path from router R1 to R8 is underused and the longest path is overused Traffic from 10.1.1 1 to 10 8 8 8 is routed on the longest path Traffic between the R1 and the application server is experiencing packet drops and latency problems.
Which action resolves the issue?

Configure route leaking for the IP address Of the application server on router RI.

Increase the RI to R2 link metric to 20.

Configure a Level 2 IS-IS domain on router RI.

Block the advertisement of the application server IP address to router R6.

Q47. Refer to the exhibit.

Router 1 has established an SR-TE tunnel with router 2. Which statement describes this configuration?

Router 1 has a list of labels used to explicitly lay out a path to router 2.

Router 1 and router 2 have a bidirectional tunnel set up with dynamic path selection.

Router 1 is the head-end tunnel and has dynamically chosen a path to router 2.

Router 2 is the head-end tunnel and has explicitly set a path to router 1.

Q48. Refer to the exhibit.

R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between BGP peers R1, R2 and R1, R3 is true?

The BGP session does not come up between R1 and R2 and between R1 and R3.

The BGP session comes up between R1 and R2 and between R1 and R3.

The BGP session comes up between R1 and R3, but not between R1 and R2.

The BGP session comes up between R1 and R2, but not between R1 and R3.

Q49. Refer to the exhibit.

P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other. Which action fixes the issue?

Change HMAC-MD5 to HMAC-SHA1-20

Configure the send and accept lifetime under key 1

Change HMAC-MD5 to MD5

Change HMAC-MD5 to HMAC-SHA1-12

Q50.

Refer to the exhibit. After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?

The two routers cannot authenticate with one another.

The two routers have the same area ID.

The two routers have the same network ID.

The two routers have different IS-types.

Q51. Refer to the exhibit.

Which tree does multicast traffic follow?

shared tree

MDT default

source tree

MDT voice

Q52. Refer to the exhibit.

After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?

The two routers cannot authenticate with one another.

The two routers have the same area ID.

The two routers have the same network ID.

The two routers have different IS-types.

Q53. Which multicast routing protocol is most optimal for supporting many-to-many multicast applications?

PIM-SM

PIM-BIDIR

MP-BGP

DVMRP

MSDP

Q54. Refer to the exhibit. An engineer working for a private telecommunication company with an employee id: 1234:56:789 notices that the customer network going through AS30-AS65001- AS65000 is experiencing packet drops when it accesses an application at 172.16.20.1/32 in the DC cloud. The BGP link between AS20 and AS30 is inaccessible because of a fiber cut. Routers RL, RN, and RZ are configured with confederation identifier 10. Which action resolves this issue?

RX(config)#router bgp 65001
RX(config-router)# bgp confederation peers 65000

RB(config)#router bgp 30
RB(config-router)# neighbor 10.10.10.3 remote-as 65001

RM(config)#router bgp 65000
RM(config-router)# bgp confederation peers 65001

RX(config)#router bgp 65001
RX(config-router)# no synchronization
RX(config-router)# bgp confederation identifier 10

Q55. Refer to the exhibit. IS-IS is the IGP for the network, where routers R1, R2, R3, and R4 are Level
1 routers in Area 12 and routers R5 and R6 are Level 2 routers in area 16. According to the network design, router R1 must send traffic to R6 using R4 as its next hop. To meet the requirement, a network engineer configured route filtering on R2 to prevent the route to R6 from being advertised from R2. However, R1 is still using R2 as the next hop. Which action must the engineer take to resolve the issue?

Move all routers into the same IS-IS area.

Disable wide area metrics and use only cost to perform the route manipulation.

Manipulate link costs to provide the desired routing through R4.

Configure routers R5 and R6 as Level 1/2 routers.

Q56. Refer to the exhibit.

P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other. Which two actions fix the issue? (Choose two.)

Change MD5 to HMAC-SHA1-12

Change MD5 to HMAC-ESP

Change MD5 to SHA-1

Change MD5 to HMAC-MD5

Remove the send and accept lifetime under key 1

Q57. Refer to the exhibit.

Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3. Which action corrects the problem?

Configure R3 to use metric-type 1 with a higher metric than R4.

Configure R1 with a static route to the R5 networks and set R5 as the next hop.

Reconfigure R1 in Area 0.

Change the metric-type value on R3 to 2.

Q58. Refer to the exhibit.

A service provider is running IS-IS in the core, and all routers use the default IS-IS configuration and reside in the same area. All routers maintain a different 6 bytes for the system ID. but the attached bits in the NET are the same. After an engineer added router R6 to the network. R3 and R5 began to experience CPU processing issues. Which action must the engineer take to resolve the issue?

Configure all routers lo operate as IS-IS Level 1 routers by altering the attached bit to ensure that a default route is Injected Into the routing tables.

Configure R6 to operate as a Level 1 router only so that it maintains the Level 1 database for all routers.

Configure routers R5 and R3 to operate as Level 1 routers only so that they inject a default routing into the routing tables of the other routers

Configure all routers to operate as IS-IS Level 2 routers so that only a Level 2 database is maintained.

Q59. What is the difference between RPL and route map actions?

RPL uses match, set, drop, and stop actions, and route maps use match, set, and drop actions

RPL uses match, pass, set, and drop actions, and route maps use match, set, and drop actions.

RPL uses pass, set, and drop actions only, and route maps use match, set, and drop actions.

RPL uses pass, set, drop, and done actions, and route maps use match and set actions only.

Q60. Refer to the exhibit. Routers within the cluster are not receiving the desired prefixes.
What must be done to fix the issue?

Clients in that cluster must have full mesh connectivity between eBGP peers.

No client-to-client must be disabled.

Clients in that cluster must have full mesh connectivity between iBGP peers.

No client-to-client reflection must be enabled.

Q61. Refer to the exhibit.

The green policy is designed with low delay, and the pink policy is designed with low cost. What is the next hop for node A on its way to node D, with the objective of achieving a low delay?

192.168.3.2

192.168.1.6

192.168.3.6

192. 168.1.2

Q62. Refer to the exhibit. An engineer working for a private telecommunication company with an employee id 4115 46 881 is enabling a segment routing solution with these requirements.
– A service provider is using the default range for prefix SID.
– PE1 must allocate the first SID from the default range for the
loopback address
– PE1 and PE2 loopback SID allocation should have a minimum difference
of 500.
Which configuration must be implemented to meet the requirements?

Option A

Option B

Option C

Option D

Q63. Refer to the exhibit.

VPN users that are connected to PE routers are facing network issues. Traffic that originates from CE1 drops before reaching CE2. An engineer finds no outgoing traffic statistics on PE1 and PE2 routers toward CE devices and finds that the PE1 router is running the older software image. Which action must be implemented to resolve the issues?

Enable LDP protocol on PE1 and PE2 routers.

Advertise P1 router loopback on PE1 in OSPF.

Enable CEF-based forwarding on PE1 router.

Advertise PE2 router loopback on PE1 in OSPF.

Q64. Refer to the exhibit. There is a connectivity issue between Customer-1 and Customer-2 File servers between the customers cannot send critical data R3 routes are missing from the routing table on the Customer-1 router. All interfaces on Customer-1 are up.
Which configuration must be applied to router R2 to correct the problem?