[Jul-2022] Updated and Accurate 500-920 Questions & Answers for passing the exam Quickly [Q19-Q43]

Rate this post

[Jul-2022] Updated and Accurate 500-920 Questions & Answers for passing the exam Quickly

Download Real 500-920 Exam Dumps for candidates. 100% Free Dump Files

Q19. You are in the process of upgrading your UCS M3 Server to a newer UCS M4 Server. You associate the Service Profile to the new UCS Server, but it fails to boot You suspect of a failed boot hard drive. You check your RAID1 Boot LUN in UCS Manager, but see no error messages What could be causing the issue?

The newer Cisco UCS M4 Server is using flash drives, not hard drives

The newer Cisco UCS M4 Server is using disks of larger capacity than the previous UCS M3 Server

A misconfiguration on the Service Profile Local Boot Policy

A misconfiguration on the Service Profile Local Disk Policy

Q20. Which statement best describes managing Cisco UCS servers using NX-OS CLI on the Fabric Interconnects?

The NX-OS CLI on the Fabric Interconnects allows you to view, but not change the connectivity configuration between the Fabric Interconnects and an upstream LAN switch.

The NX-OS CLI on the Fabric Interconnects allows you to manage QoS parameters on the Fabric Interconnects and an upstream LAN switch

The NX-OS CLI on the Fabric Interconnects allows you to change the connectivity configuration between the servers and Fabric Interconnects

The NX-OS CLI on the Fabric Interconnects allows you to change the connectivity configuration between the Fabric Interconnects and an upstream LAN switch.

Q21. After installing a new UCS M4 server, which two Cisco Integrated Management Controller connectivity options do you have? (Choose two )

XML API Access

Web Access

In-band Access

SNMP

Out-of-Band Access

Q22. Which two ports on a pair of Cisco Fabric Interconnects must be properly cabled for the pair to form a cluster? (Choose two )

L1 > L1

L1 > L2

L2 > L2

L2 > L1

Q23. Which command sequence is required to reset Cisco Integrated Management Controller (IMC) of a Cisco UCS Server?

connect cimc | reset | validate

scope cimc | reset | commit-buffer

connect cimc | reset | commit

scope cimc | reset | validate

Q24. What is the next step after performing a UCS firmware upgrade, and downloading the latest drivers both for your RAID Controller and your Fibre Channel HBA?
Check the HCL

No Drivers are needed in a UCS environment

Apply the device driver update to the devices

No need to do anything Drivers are automatically installed for you

Test device driver compatibility

Q25. In a Cisco UCS Manager, if all KVM sessions to each server fail to start, what is likely causing the problem?

Cisco UCS Manager has a problem

The Fabric Interconnect to which you are connected has a problem

The I/O Modules in the chassis are the problem

The workstation you are using to connect to the KVM session is the problem

Q26. When it comes to pinning vNIC traffic from a UCS Server to the Fabric Interconnect uplink what configuration can you perform?

You can configure Automatic Uplink Pinning. If an uplink interface fails on one Fabric Interconnect, the server will fail to the first available uplink on the other Fabric Interconnect

You can configure Static Uplink Pinning. If an uplink interface fails on one Fabric Interconnect, the server will fail to the first available uplink on the other Fabric Interconnect

You can configure Automatic Uplink Pinning. If an uplink interface fails on one Fabric Interconnect the server will fail to the matching uplink on the other Fabric Interconnect

You can configure Static Uplink Pinning. If an uplink interface fails on one Fabric Interconnect, the server will fail to the first available uplink on the same Fabric Interconnect

You can configure Static Uplink Pinning. If an uplink interface fails on one Fabric Interconnect the server will fail to the matching uplink on the other Fabric Interconnect

Q27. A Hard Drive (HDD) has been hot swapped in a UCS server blade, however, the UCS Manager GUI is not displaying updated metrics about the replacement drive. What action will be required to properly display updated metrics?

Remove and re-insert the server blade HDD controller mezzanine card

Reboot the Fabric Interconnects

Reboot the server.

Use the CLI, since HDD metrics cannot be displayed with the UCS Manager GUI

Q28. What three options should be verified, when you are able to connect to Cisco UCS Manager, but unable to open a KVM session to a blade? (Choose three)

Verify TCP port 2068 is not blocked by an ACL or Firewall

Confirm the IP Address assigned to UCS Manager is the same as the KVM address

Verify the KVM IP Address is on the same ip subnet as the virtual machines

Confirm the KVM IP Address is added to the route table in Cisco UCS Manager

Confirm the IP Address assigned to the KVM is not a duplicate IP

Verify the KVM IP Address is on the same subnet as the Fabric Interconnect management address

Q29. Which statement is true regarding the UCS Manager GUI is showing “Overall Status Unassociated” in the General tab for a C-series server?

The server has a service profile assigned, but has connectivity issues with UCS Manager

The server is not properly connected

The server does not have a service profile assigned, but has been discovered by UCS Manager

The server has been properly connected, but has not been discovered by UCS Manager

Q30. When booting up a Cisco UCS Server you want to see boot time diagnostic messages of the POST, what action is required for you to do so?

Enable Quiet Boot on the Server’s BIOS

Restart the Server

Disable Fast Boot on the Server’s BIOS

Enable Quiet Boot on the Server’s Service Profile

Disable Fast Boot on the Server’s Service Profile

Q31. You are experiencing intermittent connectivity issues on one specific Cisco UCS server Some applications work, while other do not transfer data You suspect jumbo frames limitations Which two places do you check the jumbo frame settings? (Choose two )

Check server’s service profile and/or service profile template

Check server’s QoS System Class

Check the fibre channel port configuration for jumbo frame configuration

Check upstream switch ports frame size configuration

Check server’s individual vNICs and/or vHBAs properties

Q32. Which two interfaces allow access to Cisco UCS Manager? (Choose two )

Cisco KVM

Cisco UCS Manager XML API

Cisco IMC

Cisco UCS Manager GUI

Q33. Which two statements describes connecting the IO Modules in the UCS chassis to the Fabric interconnects? (Choose two )

Connect Fl-A to the IOM B of each chassis

Connect Fl-B to IOM A and IOM B in each chassis

Connect Fl-A to the IOM A of each chassis

Connect Fl-A to IOM A and IOM B in each chassis

Connect Fl-B to the IOM A of each chassis

Connect Fl-B to the IOM B of each chassis

Q34. When troubleshooting, which option is the primary uses of the SCOPE command?

The SCOPE command is not helpful in this case

To access the log files on the log server

To access the log files that reside in a component

To access the log files on the virtual machines

Loading …

Cisco 500-920 Exam Syllabus Topics:

Topic	Details
Topic 1	Troubleshoot FEX
Topic 2	Troubleshoot storage area networks, including Fibre Channel, FCoE, zoning, NPV, and NPIV
Topic 3	Troubleshoot data center unified computing
Topic 4	Troubleshoot virtualization solutions

Prepare Important Exam with 500-920 Exam Dumps: https://www.free4dump.com/500-920-braindumps-torrent.html

Cisco 500-920 Exam Syllabus Topics:

You may also like

Leave a Reply Cancel reply