[Jul-2022] NACE-CIP1-001 Free PDF from Free4Dump [Q30-Q54]

Rate this post

Jul-2022 Latest Free4Dump NACE-CIP1-001 Exam Dumps with PDF and Exam Engine Free Updated Today!

Following are some new NACE-CIP1-001 Real Exam Questions!

NEW QUESTION 30
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:

Use another method as the comparator method is too subjective

Record the segment with the more aggressive profile

Record the segment with the less aggressive profile

Record your result by identifying two segments

NEW QUESTION 31
A NACE Coating Inspector is permitted to transport coating material when:

Asked to do so by the Coating Application team

Asked to do so by the Owner’s Representative

The Inspector should never transport coating material

If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods

NEW QUESTION 32
You ate the NACE Inspector on a job where NACE No. 2/SSPC – SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:

Review the relevant standard with the Contractor

Permit coating to take place so as not to lose the blast

Call your supervisor

Shut the job down

NEW QUESTION 33
ISO SA 2.5 is defined as:

Near White Metal Blasting

Thorough Blast Cleaning

Very Thorough Blast Cleaning

Light Blast Cleaning

NEW QUESTION 34
An inspectors personal log book should contain:

Subjective comments re ding the application team

Objective comments regarding the application work

No comments regarding the application team

The inspector’s personal opinions of the application team

NEW QUESTION 35
Removal of welds splatter is required:

On every job

When ISO abrasive blast standards are specified

When NACE/SSPC abrasive blast standards are specified

When specifically identified in the owner’s specification

NEW QUESTION 36
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:

True

False

NEW QUESTION 37
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:

High Relative Humidity

Low Relative Humidity

High Surface Temperature

Low Surface Temperature

NEW QUESTION 38
The least effective method of surface cleaning is most likely

water blasting.

dry grit blasting.

hand tool cleaning.

power tool cleaning.

NEW QUESTION 39
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply

Using a damaged gauge

Dragging a gauge through wet coating

Placing the gauge along the longitudinal axis

NEW QUESTION 40
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use

a recognized industry standard like SSPC-PA 2 that is broadly accepted

NACE 2/SSPC SP10

their best judgment based on similar projects and specifications.

a detailed checklist and document the lack of a standard.

NEW QUESTION 41
Non Conformance Reports are completed by the Inspector:

In every instance that an item does not meet the specification requirements

When the Inspector deems it to be a significant non-conforming item

When the Inspector and Contractor deem it to be a significant non-conforming item

In accordance with the specification’s definition of a non-conformance

NEW QUESTION 42
Owners hire NACE Inspectors’ with the expectation that:

The inspection cost will be offset by an improvement in service life

The Inspector will improve job flow and schedule

The Inspector will make a meaningful technical contribution to the job

a) and c)

NEW QUESTION 43
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners’ representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

Carefully review the document and do the best you can

Minimize your lack of understanding and go ahead with the inspection task to the best of your ability

Advise the owners’ representative of your lack of knowledge in this area

Hire a third patty to assist you in understanding the document

NEW QUESTION 44
Checking is

an exposed area of the substrate or previous coat material, caused by poor application technique.

a fine crack in the surface of a coating that rarely reaches the substrate

a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.

surface breaks in the film that often result from grease or oil contamination and revel the substrate.

NEW QUESTION 45
Which is a component that supplies most of the features and functions of the material?

pigment

binder

solvent

additive

NEW QUESTION 46
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?

70% of the specified maximum thickness

80% of the specified minimum thickness

90% of the specified maximum thickness

100% of the specified maximum thickness

NEW QUESTION 47
ISO SA 2 is defined as:

Near White Metal Blasting

Thorough Blast Cleaning

Very Thorough Blast Cleaning

Light Blast Cleaning

NEW QUESTION 48
Which of these tests uses a syringe?

Sleeve test

Potassium ferricyanide

Bresle patch

Soluble salts meter

NEW QUESTION 49
If a Thermoset coating is heated it will:

Harden and retain its hardness when cooled

Harden and return to its original hardness when cooled

Soften when heated and return to its original hardness when cooled

Soften when heated and retain its softness when cooled

NEW QUESTION 50
The most important factor resulting in improved job site safety is:

Personal Protective Equipment

Engineering Controls

Safety Enforcement

Situational Awareness

NEW QUESTION 51
The Inspector’s Log Book is generally:

Retained by the inspector upon project completion

Submitted to the client upon project completion

Shared with all parties upon project completion

Shredded by the inspector upon project completion

NEW QUESTION 52
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply

Failing to determine the base metal reading (BMR)

Rotating the dial too fast when taking measurements

Taking measurements too far from the edge of a surface

Measuring ditty, tacky, or soft films

NEW QUESTION 53
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:

Go with the majority opinion

Never change his/her mind

Achieve consensus through negotiation

Call the supervisor

NEW QUESTION 54
A magnetic pull-off type gauge is a good choice when:

Accuracy is not required

When an intrinsically safe tool is required