Skip to content

Free certification exam prep

  • HOME
  • ALL EXAMS
  • SAP
  • Amazon
  • Cisco
  • CompTIA
  • Google
  • HP
  • Huawei
  • Microsoft
  • Oracle
  • Salesforce
  • Contact
  • Home
  • 2024
  • June
  • 8
  • 5V0-22.23 PDF Dumps Real 2024 Recently Updated Questions [Q34-Q56]

5V0-22.23 PDF Dumps Real 2024 Recently Updated Questions [Q34-Q56]

Posted on June 8, 2024 By freedumps No Comments on 5V0-22.23 PDF Dumps Real 2024 Recently Updated Questions [Q34-Q56]
5V0-22.23, VMware
Rate this post

5V0-22.23 PDF Dumps Real 2024 Recently Updated Questions

Released VMware 5V0-22.23 Updated Questions PDF

VMware 5V0-22.23 certification exam is designed to test the knowledge and skills of IT professionals who specialize in VMware vSAN. VMware vSAN Specialist (v2) certification exam is intended for individuals who seek to demonstrate their expertise in vSAN technology and its deployment in modern data centers. 5V0-22.23 exam is a comprehensive assessment of candidates’ knowledge of vSAN architecture, administration, and management.

 

NEW QUESTION 34
A vSAN administrator notices that the VMware Skyline Health: Network Latency Check reports indicate that three hosts are noncompliant.
Which action should the vSAN administrator take?

 
 
 
 
Explanation
The correct answer is B, check VMKNICs, uplinks, physical switches, and associated settings. This is because the VMware Skyline Health: Network Latency Check reports the network latency between vSAN hosts and displays the network latency in real time. Failure indicates that the network latency is above the normal threshold, which can affect the performance and availability of vSAN. The network latency can be caused by various factors, such as misconfiguration, congestion, or errors in the network components. The vSAN administrator should check the VMKNICs, uplinks, physical switches, and associated settings for any issues and resolve them accordingly. The vSAN administrator can also use tools such as vmkping or esxtop to test the network connectivity and performance between hosts. The other options are incorrect for the following reasons:
A, immediately reboot the non-compliant hosts, is incorrect because rebooting the non-compliant hosts is not a recommended action and can cause more disruption and data loss than resolving the network issue. Rebooting the hosts will also trigger a resynchronization of data across the cluster, which can affect the performance and availability of vSAN.
C, rerun the VMware Skyline Health: vSAN Cluster Partition report, is incorrect because rerunning the VMware Skyline Health: vSAN Cluster Partition report will not help to resolve the network latency issue. The vSAN Cluster Partition report checks if there are any network partitions in the cluster that prevent communication between hosts. The network partition can be caused by network latency, but it is not the same as network latency. The vSAN administrator should first fix the network latency issue before checking for any network partitions.
D, place the non-compliant hosts into an isolated network partition, is incorrect because placing the non-compliant hosts into an isolated network partition will not help to resolve the network latency issue.
It will also cause more problemsfor vSAN, such as data inconsistency, reduced redundancy, and degraded performance. The vSAN administrator should avoid creating any network partitions in the cluster and ensure that all hosts can communicate with each other. References:
VMware vSAN Specialist v2 Exam Preparation Guide, page 9
Network Health – Network Latency Check (2149511)

NEW QUESTION 35
What is the purpose of host rebuild reserve in vSAN?

 
 
 
 
Explanation
The host rebuild reserve is a feature that allows vSAN to reserve space in the cluster for vSAN to be able to repair in case of a single host failure. This reservation is set to one host worth of capacity, which means that if one host in the vSAN cluster fails and no longer contributes storage, there is still sufficient capacity remaining in the cluster to rebuild and re-protect all vSAN objects. This feature prevents the creation of new VMs or powering on VMs if such operations consume the reserved space. By default, the host rebuild reserve is disabled, but it can be enabled in the vSAN Services configuration. The other options are not related to the hostrebuild reserve. References: vSAN Capacity Management in v7.0U1; Configure Reserved Capacity

NEW QUESTION 36
A customer has deployed a new vSAN Cluster with the following configuration:
* 6 x vSAN ReadyNodes
* All Flash
* 12 TB Raw Storage
* vSAN 8 is deployed with ESA.
VMs are configured with a RAID-5 VM policy.
During failure testing, before the new platform is placed into production one of the ESXi hosts is made unavailable.
Which RAID-5 data placement schemes will vSAN use with this failure condition?

 
 
 
 
Explanation
When a host in a vSAN stretched cluster goes offline, the data components on the hosts will be marked as degraded. This means that the data is still available, but the redundancy level is reduced. vSAN will try to rebuild the missing components on another host in the same fault domain, if there is enough capacity and resources. If the host comes back online within 60 minutes, vSAN will resync the data and restore the redundancy level. If the host does not come back online within 60 minutes, vSAN will rebuild the missing components on another fault domain, if there is enough capacity and resources. This will incur additional network traffic across the witness link. References: VMware vSAN Specialist v2 EXAM 5V0-22.23, page 17

NEW QUESTION 37
An administrator has successfully deployed a vSAN Stretched Cluster and needs to ensure that any virtual machines that are created are placed in the appropriate site.
Which two steps are needed to complete this task? (Choose two.)

 
 
 
 
 
Explanation
To ensure that any virtual machines that are created are placed in the appropriate site, the administrator needs to create VM/Host groups for the two sites and create a storage policy that includes site affinity rules and apply to VMs. VM/Host groups allow the administrator to group virtual machines and hosts based on their location or preference. Site affinity rules specify which site a virtual machine should be placed on or prefer to run on. A single VM/Host group across both sites would not allow the administrator to control the placement of virtual machines. Putting the VMs in a vSphere DRS group or in the correct VM group would not affect their site affinity. References: 1, page 12; 2, section 3.2

NEW QUESTION 38
A vSAN administrator is planning to deploy a new vSAN cluster with these requirements:
* Physical adapters share capacity among several traffic types
* Guaranteed bandwidth for vSAN during bandwidth contention
* Enhanced security
Which two actions should be taken to configure the new vSAN cluster to meet these requirements? (Choose two.)

 
 
 
 
 
Explanation
Utilizing Network I/O Control and isolating vSAN traffic in a VLAN are the two actions that should be taken to configure the new vSAN cluster to meet the requirements. Network I/O Control allows the vSAN administrator to create network resource poolsand assign bandwidth shares or reservations to different traffic types, such as vSAN, vMotion, or management. This ensures that vSAN traffic has guaranteed bandwidth during contention and can achieve better performance and availability. Isolating vSAN traffic in a VLAN enhances the security of the cluster by preventing unauthorized access or interference from other network segments. It also simplifies the network configuration and management by reducing the broadcast domain and avoiding IP address conflicts. Creating static routes between the vSAN hosts, using IOPS Limit rules in storage policies, and enabling jumbo frames are not necessary or recommended actions for this scenario. Static routes are not required for vSAN communication, as vSAN uses multicast or unicast depending on the version and configuration. IOPS Limit rules are used to limit the IOPS allocated to an object, which can degrade the performance and latency of the application. Jumbo frames can improve the network efficiency and throughput, but they are not mandatory for vSAN and require consistent configuration across all network devices.
References:
Network I/O Control
vSAN Network Design Guide

NEW QUESTION 39
An all-flash vSAN ESA cluster contains four nodes.
Which two storage policies can the cluster satisfy? (Choose two.)

 
 
 
 
 
Explanation
An all-flash vSAN ESA cluster with four nodes can satisfy the storage policies that require FTT=2 (RAID-1 Mirroring) or FTT=2 (RAID-6 Erasure Coding). These policies mean that the cluster can tolerate two host failures while maintaining data availability and redundancy. RAID-1 Mirroring creates three replicas of each object across different hosts, while RAID-6 Erasure Coding splits each object into four data segments and two parity segments across different hosts. Both policies require at least four hosts in the cluster to meet the FTT=2 requirement. The other options are not correct. An all-flash vSAN ESA cluster with four nodes cannot satisfy the storage policies that require FTT=3 (RAID-1 Mirroring) or FTT=1 (RAID-5 Erasure Coding). These policies mean that the cluster can tolerate three or one host failure respectively, but they require more or less hosts than four to do so. RAID-1 Mirroring with FTT=3 requires at least six hosts in the cluster to create four replicas of each object, while RAID-5 Erasure Coding with FTT=1 requires at least three hosts in the cluster to split each object into two data segments and one parity segment. References: vSAN Express Storage Architecture; RAID Configurations, FTT, and Host Requirements

NEW QUESTION 40
A vSAN administrator is using the vSAN ReadyNode Sizer to build a new environment. While entering the cluster configurations, a fellow colleague inquires about the Operations Reserve option.
What is the purpose of using this option?

 
 
 
 
Explanation
The purpose of using the Operations Reserve option in the vSAN ReadyNode Sizer is to provide space for internal operations such as deduplication, compression, encryption, snapshots, clones, and rebalancing. The Operations Reserve is calculated as a percentage of the total usable capacity of the vSAN cluster. The default value is 30%, but it can be adjusted based on the expected workload characteristics and data services requirements. The other options are not correct, as they do not describe the Operations Reserve option. Configuring space for external operations, reserving space for tolerating failures, and allocating space for vSAN upgrades are not part of the Operations Reserve option. References: 2, section 2; , section 3

NEW QUESTION 41
A customer wants to validate if Skyline online health is working for vSAN and finds out that Skyline is not fully configured yet.
What two requirements must be met to make sure that Skyline online health will work? (Choose two.)

 
 
 
 
 
Explanation
To make sure that Skyline online health will work for vSAN, two requirements must be met: enable CEIP and join the program, and have a working Internet connection. CEIP stands for Customer Experience Improvement Program, which is a voluntary program that collects anonymous product usage data from customers who participate in it. By enabling CEIP and joining the program, customers can benefit from Skyline online health, which provides proactivenotifications and recommendations for software and hardware issues based on VMware Analytics Cloud. A working Internet connection is also required for Skyline online health to communicate with VMware Analytics Cloud and receive online notifications. The other options are not requirements for Skyline online health. References: About the vSAN Skyline Health; Skyline Health

NEW QUESTION 42
How often does the Skyline Health interval validate online if there are new Health Checks available for vSAN?

 
 
 
 
Explanation
The Skyline Health interval validates online if there are new Health Checks available for vSAN every 24 hours. This means that vSAN checks for new health checks from VMware Analytics Cloud once a day and updates the vSAN Health Service accordingly. The other options are not correct, as they do not match the actual frequency of the online validation. References: About the vSAN Skyline Health

NEW QUESTION 43
Which two considerations should an architect assess when designing a HCI Mesh solution with VMware vSAN and VMware vSphere High Availability (HA)? (Choose two.)

 
 
 
 
 
Explanation
To design a HCI Mesh solution with VMware vSAN and VMware vSphere High Availability (HA), two considerations that the architect should assess are: A minimum of three nodes are required within the client cluster for vSphere HA to work. This is because vSphere HA needs at least three nodes in a cluster to form a quorum and elect a master host that monitors the availability of other hosts and VMs. If there are less than three nodes in a cluster, vSphere HA cannot function properly and might fail to detect or respond to host or VM failures. If vSphere HA is to work with HCI Mesh, Datastore with All Paths Down (APD) must be configured to Power off and restart VMs. This is because APD is a condition that occurs when a storage device becomes inaccessible due to loss of physical connectivity, resulting in I/O errors or timeouts for VMs that use that device. When using HCI Mesh, APD can happen if the network connection between the client cluster and the server cluster is lost or disrupted, causing the remote datastore to become unavailable. To ensure that vSphere HA can restart the affected VMs on another host that has access to their storage, Datastore with APD must be set to Power off and restart VMs in the vSphere HA settings. The other options are not correct. A server vSAN cluster can serve its local datastore up to 15 client vSAN clusters, not five. This is the maximum number of client clusters that can mount a remote datastore from a server cluster using HCI Mesh.
A client cluster can mount up to five remote datastores from one or more vSAN server clusters, not ten. This is the maximum number of remote datastores that can be mounted by a client cluster using HCI Mesh.
References: VMware vSAN HCI Mesh; vSphere Availability; Handling All Paths Down (APD) Conditions

NEW QUESTION 44
What are two characteristics of a durability component in vSAN? (Choose two.)

 
 
 
 
 
Explanation
A durability component is a temporary component that is created when a host or disk group is placed in maintenance mode with the Ensure data accessibility option, or when a host or disk group fails unexpectedly.
A durability component improves the availability of data by maintaining the required number of failures to tolerate (FTT) until the original component is restored or rebuilt. A durability component also speeds up the resynchronization process by reducing the amount of data that needs to be copied. The other characteristics are not applicable to a durability component. References: VMware vSAN Specialist v2 EXAM 5V0-22.23, page
10, Objective 6.8; [Durability Components]

NEW QUESTION 45
An administrator is tasked to create a Kerberos secured NFS v4.1 file share.
Which information is minimally required during the configuration of the File Service?

 
 
 
 
Explanation
To create a Kerberos secured NFS v4.1 file share, the administrator needs to provide the following information during the configuration of the File Service:
Active Directory Domain: The domain name of the Active Directory server that provides Kerberos authentication service for the NFS server and clients. For example, example.com.
User Account: The user name of the Active Directory account that has permissions to join the NFS server to the domain and create service principal names (SPNs) for the NFS server. For example, [email protected].
Password: The password of the Active Directory account that is used for authentication. For example, P@ssw0rd.
These information are required to enable Kerberos security for NFS 4.1 and allow the NFS server to obtain a Kerberos ticket from the Active Directory server. The administrator also needs to specify the NFS share name, path, and access permissions1 References: 1: VMware vSphere Storage Guide, page 118

NEW QUESTION 46
An administrator is upgrading multiple vSAN Witness nodes with vLCM (single image management) that are used for vSAN Stretched and two-node Clusters.
What two witness node types can the administrator upgrade? (Choose two.)

 
 
 
 
 
Explanation
To upgrade multiple vSAN Witness nodes with vLCM (single image management) that are used for vSAN Stretched and two-node Clusters, the administrator can upgrade two witness node types: appliance witness node and nested witness node. An appliance witness node is a virtual ESXi host that runs on a physical ESXi host and contains the witness components of VM objects stored in the vSAN cluster. A nested witness node is a virtual ESXi host that runs on another virtual ESXi host and contains the witness components of VM objects stored in the vSAN cluster. Both types of witness nodes can be managed by vLCM as independent nodes since vSphere 7.0 Update 3, as long as they are version 7.0 Update 2 or later. The other options are not correct. A shared witness node is a witness node that serves multiple vSAN clusters, which is not supported by vLCM. A dedicated witness node is a witness node that serves only one vSAN cluster, which is not a specific type of witness node. A physical witness node is aphysical ESXi host that contains the witness components of VM objects stored in the vSAN cluster, which cannot be upgraded by vLCM. References: vSphere Lifecycle Manager and the vSAN Witness Hosts; Shared Witness for 2-Node vSAN Deployments

NEW QUESTION 47
The DevOps team of an organization wants to deploy with persistent storage on a dedicated vSAN cluster. The storage administrator is tasked to configure the vSAN cluster and leverage the vSAN Direct feature.
Which two requirements must the administrator meet to complete this task? (Choose two.)

 
 
 
 
 
Explanation
To configure vSAN Direct, the administrator must meet two requirements: a valid vSAN license for the vSAN cluster and unclaimed disks in the hosts for vSAN Direct. A vSAN license is required to enable vSAN features and services, including vSAN Direct. Unclaimed disks are local storage devices that are not used by vSAN or any other service, and can be claimed by vSAN Direct to create datastores for persistent storage. The other options are not requirements for vSAN Direct. HA is an optional feature that can be enabled on any cluster, but is not specific to vSAN Direct. A dedicated network for vSAN Direct is not necessary, as vSAN Direct uses the same network as vSAN. An integration with vSAN File Services is not required, as vSAN Direct does not provide file shares, but block storage. References: Set Up vSAN Direct for vSphere with Tanzu; vSAN Licensing Guide

NEW QUESTION 48
A customer wishes to host a new range of applications with high-performance requirements, specifically, low latency. The current vSAN platform is based on ReadyNode hardware and uses a vSAN 7.0 U2 hybrid topology configuration.
Which would satisfy the customer’s requirement?

 
 
 
 
Explanation
Deploying the application on a new cluster with vSAN 8.0 ESA using a new hardware design is the correct answer because it will satisfy the customer’s requirement for low latency. vSAN 8.0 ESA is a new architecture that uses a storage pool configuration where all disks are treated as capacity disks and use a new algorithm to distribute data across them. This improves the I/O flow, reduces the write amplification, and eliminates the cache tier bottleneck. Using a new hardware design with all-flash disks or NVMe disks will further enhance the performance and latency of the application, as these disks have faster read and write speeds than hybrid disks. Deploying the new applications on the existing cluster with a RAID-6 VM storage policy and an additionalstripe width of 4, deploying the application on a new cluster with vSAN 8.0 OSA using the existing hybrid configuration, and performing an in-place upgrade from vSAN 7.0 U2 OSA to vSAN 8.0 ESA are not valid or optimal solutions for this scenario. Deploying the new applications on the existing cluster with a RAID-6 VM storage policy and an additional stripe width of 4 will increase the resiliency and availability of the data, but it will also increase the network traffic, disk space consumption, and parity calculation overhead, which will negatively affect the latency and performance of the application. Deploying the application on a new cluster with vSAN 8.0 OSA using the existing hybrid configuration will not improve the latency significantly, as vSAN 8.0 OSA still uses the same disk group configuration as vSAN 7.0 U2 OSA, where one disk is designated as a cache disk and the rest are capacity disks. The cache disk can still become a bottleneck for high-performance applications, especially if it is not an SSD or NVMe disk. Performing an in-place upgrade from vSAN 7.0 U2 OSA to vSAN 8.0 ESA is not possible, as vSAN ESA requires a different hardware design than vSAN OSA. The existing disk groups need to be deleted and all disks need to be erased before switching to vSAN ESA. References:
[VMware vSAN Specialist v2 Exam Preparation Guide], page 6
What’s New in VMware vSAN 8.0

NEW QUESTION 49
During yesterday’s business hours, a cache drive failed on one of the vSAN OSA nodes. The administrator reached out to the manufacturer and received a replacement drive the following day. When the drive failed, vSAN started a resync to ensure the health of the data, and all objects are showing a healthy and compliant state. The vSAN administrator needs to replace the failed cache drive.
Which set of steps should the vSAN administrator take?

 
 
 
Explanation
To replace a failed cache drive in a vSAN OSA cluster, the vSAN administrator should remove the existing vSAN disk group and physically replace the device. Then check to verify that the ESXi host automatically detects the new device Afterwards manually recreate the Disk Group. This is because when a cache drive fails, it affects the entire disk group that contains it, and vSAN does not allow removing only the cache drive from a disk group. Therefore, the administrator must remove the whole disk group before replacing the cache drive, and then recreate it with the new cache drive and the existing capacity drives. The other options are not correct. Physically replacing the failed cache drive without removing the disk group first might cause errors or inconsistencies in vSAN configuration. vSAN will not automatically create a new disk group or allocate storage after replacing a cache drive, as these actions require manual intervention from the administrator.
Rebalancing the cache layer is not necessary after replacing a cache drive, as vSAN will automatically distribute data across all devices in the disk group. References: Replace a Flash Caching Device on a Host; How to manually remove and recreate a vSAN disk group using esxcli

NEW QUESTION 50
Which VMware solution requires vSAN usage?

 
 
 
 
Explanation
The VMware solution that requires vSAN usage is VMware Cloud Foundation. VMware Cloud Foundation is an integrated software stack that bundles compute virtualization (VMware vSphere), storage virtualization (VMware vSAN), network virtualization (VMware NSX), and cloud management and monitoring (VMware vRealize Suite) into a single platform that can be deployed on premises or as a service within a public cloud.
VMware Cloud Foundation relies on vSAN as the primary storage solution for its workload domains, which are logical pools of resources that can be used to run different types of workloads. The other options are not correct. VMware Horizon, VMware Telco Cloud Automation, and VMware Aria Automation are VMware solutions that do not require vSAN usage, although they can benefit from it. VMware Horizon is a platform that delivers virtual desktops and applications across a variety of devices and locations, and it can use any supported storage solution, including vSAN. VMware Telco Cloud Automation is a cloud-native orchestration and automation platform that enables communication service providers to accelerate the deployment and lifecycle management of network functions and services across any network and cloud. It can use any supported storage solution, including vSAN. VMware Aria Automation is not a valid VMware solution name.
References: VMware Cloud Foundation Overview; VMware Horizon Overview; VMware Telco Cloud Automation Overview

NEW QUESTION 51
An organization plans to implement a new vSAN 8.0 cluster to take advantage of the new features around improved I/O flow, better resiliency, and more efficient disk usage. The vSAN ReadyNodes available for the cluster consist of eight NVMe disks.
How should the organization configure the disk layout?

 
 
 
 
Explanation
Using vSAN ESA and the new Storage pool configuration where all disks contribute to capacity is the correct answer because it allows the organization to take advantage of the new features in vSAN 8.0, such as improved I/O flow, better resiliency, and more efficient disk usage. With vSAN ESA, there is no need to create disk groups or designate cache disks, as all disks are treated as capacity disks and use a new algorithm to distribute data across them. This also simplifies the disk management and reduces the overhead of cache management. References:
VMware vSAN Specialist v2 Exam Preparation Guide, page 6
What’s New in VMware vSAN 8.0

NEW QUESTION 52
An administrator has to perform maintenance on one of the hosts in a three-node vSAN Cluster.
Which maintenance mode option will give the administrator the best availability for the VMs with the least effort and data transfer?

 
 
 
 
Explanation
To perform maintenance on one of the hosts in a three-node vSAN cluster with the best availability for the VMs with the least effort and data transfer, the maintenance mode option that should be used is Ensure accessibility. This option migrates only enough components to ensure that all accessible VMs remain accessible, but does not guarantee full data redundancy or policy compliance. This option is also the only evacuation mode available for a three-node cluster or a cluster with three fault domains, as there are not enough hosts to perform full data migration or re-protection after a failure. The other options are not correct.
Migrating all VMs and their storage from the host to a different storage system or a different vSphere cluster would require more effort and data transfer than using Ensure accessibility, as well as additional resources and configuration steps. Full data migration is not possible in a three-nodecluster, as it would require at least four hosts to evacuate all data from one host and maintain full redundancy and policy compliance.
References: Place a Member of vSAN Cluster in Maintenance Mode; Working with Maintenance Mode

NEW QUESTION 53
An administrator is deploying a new two-node vSAN cluster with a shared witness to a remote location.
Which requirement must be met?

 
 
 
 
Explanation
To deploy a new two-node vSAN cluster with a shared witness, the administrator must meet several requirements, one of which is that the ESXi hosts must have a minimum of 64 GBs of memory. This is because each host must have enough memory to run the VMs and also to support the vSAN metadata overhead. The other options are not requirements for a two-node vSAN cluster with a shared witness. The ESXi hosts do not need SSDs or NVMe for Virtual Flash File System, as they can use any supported storage devices for vSAN. The ESXi host’s controller cache and advanced features do not need to be disabled, as they can be used to improve performance and reliability. The ESXi host’s drives do not need to be configured in RAID 1, as vSAN uses its own software-defined RAID mechanism to provide Failures to Tolerate.
References: Shared Witness for 2-Node vSAN Deployments; Two-Node Cluster Requirements

NEW QUESTION 54
An administrator has been tasked with upgrading existing vSAN OSA cluster hosts with a SSD cache device per host to a NVMe device (hot plug).
Which fact should guide the administrator’s action?

 
 
 
 
Explanation
The correct answer is A, the disk group must be deleted on each physical host in the vSAN OSA cluster to use the NVMe device. This is because vSAN OSA uses a disk group configuration where one disk is designated as a cache disk and the rest are capacity disks. To replace the cache disk with a different type or size, the disk group must be deleted first, which will erase all data on the disks and trigger a resynchronization of the affected objects. The administrator should put the host in maintenance mode and choose the option to evacuate all data before deleting the disk group. After replacing the cache disk with the NVMe device, the administrator should recreate the disk group and exit maintenance mode. The other options are incorrect for the following reasons:
B, the disk group does not need to be removed before adding new cache, is incorrect because adding a new cache disk to an existing disk group is not supported in vSAN OSA. The cache disk can only be replaced by deleting and recreating the disk group.
C, the host must be removed from vSAN OSA cluster before changing cache devices, is incorrect because removing the host from the cluster is not necessary and will cause more disruption and data loss than putting the host in maintenance mode. Removing the host will also delete its disk groups and require re-adding them after rejoining the cluster.
D, the cache disk drives must have a larger capacity, is incorrect because there is no requirement for the cache disk to have a larger capacity than the existing one. The cache disk size should be determined by the workload characteristics and performance requirements, not by the expansion process. References:
VMware vSAN Specialist v2 Exam Preparation Guide, page 10

NEW QUESTION 55
A vSAN administrator was presented with 30 additional vSAN ReadyNodes to add to an existing vSAN cluster. There is only one administrator to complete this task.
What is the fastest approach?

 
 
 
 
Explanation
To add 30 additional vSAN ReadyNodes to an existing vSAN cluster with the fastest approach, the vSAN administrator should use a Host Profile that was extracted from an existing host. AHost Profile is a configuration template that captures the settings of a reference host and applies them to other hosts or clusters.
This way, the administrator can quickly and consistently configure multiple hosts with the same settings, such as network, storage, security, and services. The other options are not correct. Running vim-cmd to capture and apply the configuration from an existing host is not as fast or convenient as using a Host Profile, as it requires running commands on each host individually. Launching Quickstart to Add Hosts to a vSAN Cluster is not possible, as Quickstart is only available for new clusters or clusters that were configured through Quickstart.
Cloning the ESXi boot partition to all new hosts is not recommended, as it might cause conflicts or errors with the host identity, network settings, or licenses. References: Configuring Hosts Using Host Profile; Using Quickstart to Configure and Expand a vSAN Cluster

NEW QUESTION 56
A vSAN administrator has a group of requirements from the application team, which mandates spreading the components across storage devices as much as possible.
What should the vSAN Administrator consider to achieve such a requirement for building a new vSAN cluster? (Choose two.)

 
 
 
 
 
Explanation
To spread the components across storage devices as much as possible, the vSAN administrator can configure disk striping in either OSA or ESA. Disk striping is a policy attribute that defines the number of capacity devices across which each replica of a storage object is striped. A higher number of stripes can result in better performance and availability, but also consumes more storage space. Disk striping can be configured in OSA by using the Number of disk stripes per object policy attribute, or in ESA by using the Striping Width policy attribute12 References: 1: VMware vSAN Specialist v2 Exam Preparation Guide, page 14 2: VMware vSAN Design and Sizing Guide, page 32

Loading ... Loading …

Loading

VMware 5V0-22.23 exam comprises 60 multiple-choice questions that need to be completed within 135 minutes. 5V0-22.23 exam covers various topics, including vSAN architecture and components, vSAN cluster design and deployment, vSAN storage policies, vSAN monitoring, and troubleshooting. To prepare for the exam, VMware recommends candidates to take the VMware vSAN: Deploy and Manage course or have equivalent knowledge and experience. Passing 5V0-22.23 exam also fulfills the prerequisite for the VMware Certified Advanced Professional – Data Center Virtualization (VCAP-DCV) Design certification. Overall, the VMware 5V0-22.23 certification exam is an essential step for IT professionals who want to demonstrate their expertise in vSAN technology and advance their careers in virtualization and cloud computing.

 

5V0-22.23 Dumps and Practice Test (75 Exam Questions): https://www.free4dump.com/5V0-22.23-braindumps-torrent.html

         

Related Links: myportal.utt.edu.tt myportal.utt.edu.tt myportal.utt.edu.tt www.stes.tyc.edu.tw myportal.utt.edu.tt github.com

Tags: 5V0-22.23 exam pattern 5V0-22.23 latest exam dumps questions 5V0-22.23 reliable braindumps ppt 5V0-22.23 reliable dumps ppt 5V0-22.23 valid exam dumps demo

Post navigation

❮ Previous Post: Share Latest Jun-2024 IIA-CIA-Part3Test Practice Test Questions, Exam Dumps [Q19-Q41]
Next Post: New (2024) Download free DP-100 PDF for Microsoft Practice Tests [Q57-Q78] ❯

You may also like

3V0-22.21
[Jun-2022] Latest VMware 3V0-22.21 Certification Practice Test Questions [Q10-Q34]
June 19, 2022
2V0-11.24
Get Latest Jan-2025 Conduct effective penetration tests using Free4Dump 2V0-11.24 [Q53-Q74]
January 23, 2025
2V0-31.23
[Full-Version] 2024 New 2V0-31.23 Actual Exam Dumps, VMware Practice Test [Q20-Q44]
August 2, 2024
2V0-72.22
Feb-2025 VMware 2V0-72.22 Actual Questions and 100% Cover Real Exam Questions [Q29-Q52]
February 27, 2025

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Enter the text from the image below
 

5V0-22.23 Practice Tests

  • 5V0-22.23 PDF Dumps Real 2024 Recently Updated Questions [Q34-Q56]

Related Certifications

  • 5V0-31.22 (1)
  • 3V0-21.21 (2)
  • 5V0-92.22 (1)
  • 2V0-11.24 (1)
  • 5V0-35.21 (1)
  • 2V0-31.23 (1)
  • 5V0-22.23 (1)
  • 3V0-22.21 (2)
  • 2V0-72.22 (1)
  • 5V0-21.21 (2)

Recent Posts

  • [Q301-Q321] Free SAP-C02 Questions for Amazon SAP-C02 Exam [Sep-2026]
  • Ace PCPP-32-101 Certification with 71 Actual Questions [Q41-Q65]
  • [Sep 27, 2026] Get Latest and 100% Accurate Databricks-Machine-Learning-Professional Exam Questions [Q36-Q51]
  • ISA-IEC-62443 Premium PDF & Test Engine Files with 221 Questions & Answers [Q87-Q107]
  • [Sep-2026] ITILFND_V4 Exam Dumps – Free Demo & 365 Day Updates [Q44-Q60]

Archives

  • September 2026 (17)
  • August 2026 (20)
  • July 2026 (9)
  • May 2026 (10)
  • April 2026 (8)
  • March 2026 (23)
  • February 2026 (23)
  • January 2026 (13)
  • December 2025 (22)
  • November 2025 (2)
  • October 2025 (4)
  • September 2025 (9)
  • August 2025 (8)
  • July 2025 (5)
  • April 2025 (6)
  • March 2025 (10)
  • February 2025 (16)
  • January 2025 (18)
  • December 2024 (10)
  • November 2024 (14)
  • October 2024 (19)
  • September 2024 (7)
  • August 2024 (4)
  • July 2024 (13)
  • June 2024 (22)
  • May 2024 (11)
  • April 2024 (4)
  • March 2024 (18)
  • February 2024 (15)
  • January 2024 (29)
  • December 2023 (42)
  • November 2023 (28)
  • October 2023 (24)
  • September 2023 (20)
  • August 2023 (14)
  • July 2023 (18)
  • June 2023 (17)
  • May 2023 (19)
  • April 2023 (30)
  • March 2023 (13)
  • February 2023 (28)
  • January 2023 (23)
  • December 2022 (36)
  • November 2022 (21)
  • October 2022 (21)
  • September 2022 (16)
  • August 2022 (35)
  • July 2022 (29)
  • June 2022 (33)

Categories

  • A10 Networks (1)
  • AACE International (1)
  • AACN (1)
  • ACAMS (4)
  • ACT (1)
  • Adobe (11)
  • AFP (1)
  • AGA (1)
  • AICPA (1)
  • Alibaba Cloud (2)
  • Amazon (16)
  • APMG-International (3)
  • ASIS (1)
  • ASQ (5)
  • ATLASSIAN (2)
  • Avaya (3)
  • BACB (1)
  • BCS (7)
  • BICSI (2)
  • Blue Prism (1)
  • Broadcom (1)
  • Business Architecture Guild (1)
  • CCE Global (1)
  • Certinia (1)
  • CertNexus (2)
  • CheckPoint (1)
  • CIDQ (1)
  • CIMA (6)
  • CIPS (2)
  • Cisco (39)
  • CISI (1)
  • Citrix (3)
  • CIW (1)
  • Cloud Security Alliance (1)
  • CloudBees (1)
  • College Admission (1)
  • CompTIA (15)
  • Confluent (1)
  • CWNP (1)
  • DAMA (1)
  • Databricks (5)
  • Docker (1)
  • EC-COUNCIL (6)
  • ECCouncil (2)
  • EMC (10)
  • EXIN (6)
  • F5 (2)
  • Facebook (2)
  • FINRA (1)
  • Forescout (1)
  • Fortinet (21)
  • GAQM (4)
  • GED (1)
  • Genesys (2)
  • GIAC (2)
  • Google (5)
  • H3C (1)
  • HashiCorp (2)
  • Hitachi (3)
  • HP (19)
  • HRCI (1)
  • Huawei (42)
  • IAPP (6)
  • IBM (12)
  • IIA (3)
  • IIBA (3)
  • IICRC (1)
  • ISACA (6)
  • ISC (5)
  • ISM (1)
  • ISQI (4)
  • Juniper (16)
  • Linux Foundation (2)
  • Lpi (3)
  • Maryland Insurance Administration (1)
  • Medical Professional (1)
  • Microsoft (38)
  • MikroTik (1)
  • MuleSoft (3)
  • NACE (1)
  • NASM (1)
  • NBMTM (1)
  • NCLEX (1)
  • Netskope (1)
  • NetSuite (2)
  • Network Appliance (5)
  • NFPA (1)
  • NICET (1)
  • NSCA (1)
  • Nutanix (11)
  • OCEG (1)
  • OMG (1)
  • Oracle (45)
  • Palo Alto Networks (7)
  • PCI SSC (1)
  • PECB (2)
  • Pegasystems (5)
  • PMI (5)
  • PRINCE2 (2)
  • PRMIA (1)
  • Python Institute (3)
  • Qlik (3)
  • RedHat (1)
  • RUCKUS (1)
  • Salesforce (78)
  • SAP (180)
  • Scrum (10)
  • ServiceNow (12)
  • Shared Assessments (2)
  • Sitecore (2)
  • Snowflake (5)
  • Splunk (4)
  • Symantec (1)
  • Tableau (5)
  • The Open Group (2)
  • Tibco (1)
  • Trend (1)
  • Uncategorized (34)
  • Veeam (1)
  • VMware (15)
  • WGU (3)
  • Workday (1)
  • WorldatWork (1)
  • DMCA
  • Privacy Policy
  • Contact now

Copyright © 2026 Free certification exam prep.

Theme: Oceanly News by ScriptsTown